300ZX (Z31) Forums Dedicated to 84-89 ZCars otherwize known as the Z31's

Replacement Fuel Level Sending Unit

Thread Tools
 
Search this Thread
 
Old Sep 2, 2015 | 04:34 PM
  #1  
mgk1068's Avatar
Thread Starter
Registered User
 
Joined: Jul 2015
Posts: 7
From: Boston, MA
Replacement Fuel Level Sending Unit

Hi, has anyone tried the replacement fuel level sending unit from Nissan? No matter how I configure it, the needle bounces all over the place. I can see now why the old one has the cylinder around the float.

Has anyone else experienced this?

Thanks
Old Sep 2, 2015 | 05:01 PM
  #2  
zxguy1986's Avatar
Registered User
 
Joined: Aug 2013
Posts: 1,103
Yes. Fuel level sending gadget is a frequent problem with the Z31s. In my original '86na, two or three times I cleaned the wires that the floaters rode up and down but that only postponed the problem and my fixes didn't last that long. Maybe a year.

Finally bought an aftermarket replacement that I didn't adjust correctly so it always read about 4 gallons too low. For replacements, I think either aftermarket or OEM where available would be OK but you have to adjust them by installing the gadget, getting a reading and then moving the reader/sender gauge either up or down as required. You want Betty to tell you that fuel level is low without driving you crazy.

Anyway, a bouncing needle is a hint that the sending unit isn't working right or you have a bad/dirty harness circuit between sender and gauge. Check all that out before you replace the sender. Again.
Old Sep 3, 2015 | 01:11 PM
  #3  
rogerz's Avatar
Grumpy & Helpful
 
Joined: Sep 2006
Posts: 1,415
From: Mill Creek WA
replaced one digital and one analog no problems with either one. as zx said check your wiring.
Old Sep 3, 2015 | 04:40 PM
  #4  
rogerz's Avatar
Grumpy & Helpful
 
Joined: Sep 2006
Posts: 1,415
From: Mill Creek WA
what did your replacement look like. The replacement that works has floats that work arms to send the signal. the old style Iron bar with carbon tracks inside an aluminum can are no good. where did you get the "replacement"?
Old Sep 4, 2015 | 11:02 AM
  #5  
mgk1068's Avatar
Thread Starter
Registered User
 
Joined: Jul 2015
Posts: 7
From: Boston, MA
Got it from Nissan. It's the factory replacement.
Old Sep 4, 2015 | 11:03 AM
  #6  
mgk1068's Avatar
Thread Starter
Registered User
 
Joined: Jul 2015
Posts: 7
From: Boston, MA
I don't think it's the wiring because the old gauge didn't do this. It just said the tank was empty when it got down to half. The needle didn't bounce around.
Old Sep 5, 2015 | 08:01 AM
  #7  
rogerz's Avatar
Grumpy & Helpful
 
Joined: Sep 2006
Posts: 1,415
From: Mill Creek WA
that link goes to ebay often a source of junk. try courtesy nissan for a REAL nissan part not ebay factory replacement part which means someone made it in a factory and then said it is a genuine replacement

Nissan Parts, NISMO and Nissan Accessories - Courtesyparts.com

I think you bought a faulty or at least non standard replacement. get a refund

There is nothing TO CONFIGURE with a real part.
Old Sep 5, 2015 | 08:18 AM
  #8  
mgk1068's Avatar
Thread Starter
Registered User
 
Joined: Jul 2015
Posts: 7
From: Boston, MA
Thanks roger. I actually ordered it from my local Nissan dealership, part # 25060-17P65. I
didn't post a link.

Last edited by mgk1068; Sep 5, 2015 at 08:59 AM. Reason: Added part number
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
houlis1211
300ZX (Z31) Forums
7
Feb 24, 2013 07:04 PM
HexaggramJDM
300ZX (Z31) Forums
6
Jun 29, 2011 10:37 PM
rjc280z
240Z, 260Z, 280Z Performance / Technical
4
Sep 29, 2009 01:13 PM
Carl's Z
280ZX (S130) Forums
7
Sep 12, 2005 04:53 PM
ratedZ
240Z, 260Z, 280Z (S30) Forums
3
May 26, 2001 07:58 PM




All times are GMT -7. The time now is 07:26 AM.