Most are tucked away for the winter. Just have the 370Z on the road right now but I'll be transfering the insurance over the 280ZXT soon. I think I'll wire up the MS3 properly before I transfer the insurance.

I`m running the SAKURA FC 10 fuel management system,your sure to feel the difference compared to the oem ECU.Get that baby tuned and BOOOOST AWAY!

Some would call it a mess - I call it progress!

https://www.zdriver.com/forums/attac...1&d=1326691210

No AFM or Vacuum Control Modulator and brackets. I'll bet I lost 10lbs just removing this junk.

https://www.zdriver.com/forums/attac...1&d=1326691214

...and my new get-the-harness-done inspiration. Thanks Yasin! We're busy working each other into an S130 modding frenzy ;)

http://farm7.static.flickr.com/6166/...e8af7ce4_b.jpg

Awesome bro. I am super super jazzed (understatement!). I spent way too much time on DIY Autotune website this morning..laughing!

I have more questions too...oh boy.

http://a3.sphotos.ak.fbcdn.net/hphot...40825473_n.jpg

Ohhh my Christmas present finally showed up :)

Go Fast Bits Turbo Fuse (use your BOV as a Pop Off valve - why don't we see these on every turbo car?)

https://www.zdriver.com/forums/attac...1&d=1326781880

.... and my fully adjustable Recirc/BOV again from GFB. I plan on running a recirc to keep the turbo spooled and partial BOV to run in conjunction with the Turbo Fuse. I really like the GFB as it's the only fully adjustable Recirc/BOV I could find not to mention great fit and finish.

https://www.zdriver.com/forums/attac...1&d=1326781880

Wow..very nice and great idea, I need to add that same piece of mind. I did not even think that this existed.

I am not going to admit as to how much time I spent on DIY Autotune's website in the past 2 days! Laughing..

Looking forward to it..VERY Jazzed (understatement)

http://a3.sphotos.ak.fbcdn.net/hphot...40825473_n.jpg
Yasin

Hey Yasin welcome to the site! This is one of the most active S130 forums on the web so it's a good place to check out. It's about time you showed up!

I'm just working on the cabling for the dizzy and I found some nice shielded cables to keep the signal clean. I'm hoping to get that fabbed up as well as the thermostat temp sensors and injectors.

Are you using a stock coil (eg stock coil plugs?)

Early prototype of the new MegaSquirt 3 harness...... are you having second thoughts yet Yasin? ;P

https://www.zdriver.com/forums/attac...1&d=1326931825

Second thoughts? Never:023:

Starting to look a little more organized....

https://www.zdriver.com/forums/attac...1&d=1326952242

...and then.... No more and then!... and then.....

https://www.zdriver.com/forums/attac...1&d=1326954418

Huston we have fuel pump control! The mysteries of the S130 body harness fuel pump interface have been unravelled! Whoot Whoot!

"Ewwston is ready for launch

Wow I've put a ton of work into a little bundle of wires over the last two weeks but I've had some really great sucess with it all. The MS3 is running great! Went out for another test and tune today. Told my buddy that the car was running better than I've ever had it run but it felt like I needed new engine mounts as the engine was shaking a lot at idle. He kept saying it was like it had a dead miss. Anyhow we had stopped for coffee and were going to continue our run when we decided to pull the injector plugs one at a time. Pulled injector plug 6 - worse, injector 5 - worse, injector 4 - no change! Put it back on half way and it was smooooth.... arg corrosion on the injector - new injector plugs on the harness doesn't matter if the plugs on the injectors are corroded :) Wow the car is a new beast and I've only put on a cone filter, removed the AFM with a piece of pipe and a crush bent 3" exhaust all held together with the MS3. Pretty impressed how smooth and how much more power I've got by the butt dyno and no dyno tune either.

Here are some pictures - it's a pretty close to final product running prototype for the harness.

https://www.zdriver.com/forums/attac...1&d=1328503518

https://www.zdriver.com/forums/attac...1&d=1328503518

https://www.zdriver.com/forums/attac...1&d=1328503518

FricFrac you are a god!:icon_super: keep us posted please!! This is gonna be so helpful to allot of people myself included!
Thanks man
Andrew

Is there by chance a plan to add coil packs into a future harness? If I go MSnS, I'd like to go coil packs.

You mean for the six LSX coil packs sitting on the shelf beside me? You bet! I just have to get the diyautotune optical wheel for the L28 they just came out with for the distributorless ignition/sequential injection setup.

https://www.zdriver.com/forums/attac...1&d=1328534569

https://www.zdriver.com/forums/attac...1&d=1328534569

Me likey!!! When we doing mine. Lol.

We have to get yours up and running bro. I'm sure it's something simple. Maybe I'll get you to ship yours over and I can run it up on the stimulator... You still not getting anything with the dizzy? Have you been able to track an '82-83 dizzy down?

Coil Near Plug setup with LSX coil packs (truck) mounted on plate. Have to re-route some water hoses to make a little more room for a nice clean install....

https://www.zdriver.com/forums/attac...1&d=1329288356

https://www.zdriver.com/forums/attac...1&d=1329288356

Yeah I'm gonna start playing with mine again soon. The bug is itching bad. Summer is coming. I have a simulator that says the ecu works but it's gotta be something simple. I await extra power with this swap. Part of me wants to get it running from the msd box using the reluctor dizzy and fuel only. Then just do Edis and cop. I have a pick a part nearby with cheap parts. Then just machine the pulley down and install

Sorry cant edit. What doed the 3.57 use to drive 6 coils. Haven't had time to read up much.

3.57 is just the main PCB that MS 1, 2 and 3 all run on. 3.57 is the surface mount version or pre-built IIRC...

MS3 needs the MS3X daughter card to run sequential fuel and distributorless ignition.

Trying to figure out how to mount this. I think I'm going to have to re-route the heater hoses a bit.... Just mocking up on a spare engine in the garage....

https://www.zdriver.com/forums/attac...1&d=1329376691

You could space it out a tad to make room or go high mount off the valve cover.