need help!
Guest
Posts: n/a
need help!
hey guys, my 260Z 2+2 diff center has died on me, and I need to know if a diff from a 280ZX will fit in there. will it bolt in there or do I need to modify anything? if there is anyone who knows about this PLEASE help me, becuase the Z is my daily driver, and Im near crippled without a ride.
Kolts
Perth - Western Australia
Kolts
Perth - Western Australia
Guest
Posts: n/a
Re: need help!
Do you know if it's a R200 or R180?
The 260Z & 280ZX had both these diffs in them attached is a photo of each. There shouldn't be any issues with using a 280ZX R180 & there won't be any issues with using the R200. The only parts you will have to swap are the output stub axles & possibly the input yoke.
Note that the R200 is much wider than the R180, The R180 in the middle is a 240Z unit - note the bolt-in output stubs, the R180 on the right is an R30 skyline unit - it has clip-in 1/2 shafts (CV). The R200 also uses the clip-in system, and can support CV or uni 1/2 shafts.
Also note that the R180 has bolt-on aluminium side plates, the R200 uses internal bearing caps.
Ben
Adelaide
Sth Australia
IZCC#1902
240Z L31ETT
L28ET MR30 Skyline
FJ20ET DR30 Skyline RS-X
The 260Z & 280ZX had both these diffs in them attached is a photo of each. There shouldn't be any issues with using a 280ZX R180 & there won't be any issues with using the R200. The only parts you will have to swap are the output stub axles & possibly the input yoke.
Note that the R200 is much wider than the R180, The R180 in the middle is a 240Z unit - note the bolt-in output stubs, the R180 on the right is an R30 skyline unit - it has clip-in 1/2 shafts (CV). The R200 also uses the clip-in system, and can support CV or uni 1/2 shafts.
Also note that the R180 has bolt-on aluminium side plates, the R200 uses internal bearing caps.
Ben
Adelaide
Sth Australia
IZCC#1902
240Z L31ETT
L28ET MR30 Skyline
FJ20ET DR30 Skyline RS-X
Guest
Posts: n/a
Re: need help!
lemme try the file thing again - it was too big....
Ben
Adelaide
Sth Australia
IZCC#1902
240Z L31ETT
L28ET MR30 Skyline
FJ20ET DR30 Skyline RS-X
17343-diffs.jpg
Ben
Adelaide
Sth Australia
IZCC#1902
240Z L31ETT
L28ET MR30 Skyline
FJ20ET DR30 Skyline RS-X
17343-diffs.jpg
Guest
Posts: n/a
Re: need help!
Ben, thanks for the info man. looks like my diff is a R200. I;ll have it pulled out next week, and first see if it can be refurbished.
Are the R31 skyline diffs similar to the ones used on the 260Z, someone told me they were R180.
Kolts
Perth - Western Australia
Are the R31 skyline diffs similar to the ones used on the 260Z, someone told me they were R180.
Kolts
Perth - Western Australia
Guest
Posts: n/a
Re: need help!
The Japanese HR31 GTS(X)(R) have R200 LSD's, HR31 Passages have R200's. The Aussie R31's have a Bang... ummm, Borg Warner live-axle & the Silhouette's have a cone-type LSD fitted.
Ben
Adelaide
Sth Australia
IZCC#1902
240Z L31ETT
L28ET MR30 Skyline
FJ20ET DR30 Skyline RS-X
Ben
Adelaide
Sth Australia
IZCC#1902
240Z L31ETT
L28ET MR30 Skyline
FJ20ET DR30 Skyline RS-X
the Dude
Joined: Mar 2002
Posts: 381
From: Bay Area, California
Re: need help!
rebuilding the rear diff might be wind up costing a lot more than just picking up a unit from a junkyard. I think I paid $50 US for my r200 in good shape (i pulled it partially apart to find out it's been recently rebuilt) with halfshafts and moustache bar.
If it's going to be rebuilt, perhaps you may as well look into putting a cheapie LSD in there. See Phantom Grip
If it's going to be rebuilt, perhaps you may as well look into putting a cheapie LSD in there. See Phantom Grip
