1980 280zx
Thread Starter
Registered User
Joined: Jan 2005
Posts: 363
From: Quartz Hill, Ca
1980 280zx
well it has come to the unfortunate time that I get rid of my 280zx.. I have put a lot of work into the car and driven it all of 5 miles. if it doesn't sell whole I will be force to part it out. I am at the point that like most people I need the money, I would like to see it go to a nice home....
1980 280zx t-top 5 speed that has had the motor rebuilt ( .20" over bore new pistons rings and bearings, rebuilt N47 cylinder head, final compression ratio 10.25:1) all work done by adams metallizing.
New clutch, resurfaced flywheel, and new release bearing, rebuilt slave cylinder
new thermostat, Radiator hoses, water pump, new turbo oil pump
front suspension: energy suspension polyurethane bushing (control arms, sway bars).. I have polyurethane rear bushings need to be installed
Monza exhaust system from manifold back, Dual chrome tipped muffler, test pipe installed no cat
new timing chain gears chain and guide, New injectors and injector pigtails
Replace fenders, rear hatch and doors with rot free body panels
130mph speedometer from 79' 280zx and also analog clock gage set
high back seats need upholstery, body has surface rust
was in the process of converting interior to black and gray so i have some grey keck panels and various black interior parts.
1980 280zx t-top 5 speed that has had the motor rebuilt ( .20" over bore new pistons rings and bearings, rebuilt N47 cylinder head, final compression ratio 10.25:1) all work done by adams metallizing.
New clutch, resurfaced flywheel, and new release bearing, rebuilt slave cylinder
new thermostat, Radiator hoses, water pump, new turbo oil pump
front suspension: energy suspension polyurethane bushing (control arms, sway bars).. I have polyurethane rear bushings need to be installed
Monza exhaust system from manifold back, Dual chrome tipped muffler, test pipe installed no cat
new timing chain gears chain and guide, New injectors and injector pigtails
Replace fenders, rear hatch and doors with rot free body panels
130mph speedometer from 79' 280zx and also analog clock gage set
high back seats need upholstery, body has surface rust
was in the process of converting interior to black and gray so i have some grey keck panels and various black interior parts.
Last edited by flightforlife07; Dec 1, 2011 at 07:36 AM.
Thread Starter
Registered User
Joined: Jan 2005
Posts: 363
From: Quartz Hill, Ca
I havent pulled the harness yet was beginning to disassemble the car today.. I was loking ou=ver the harness as I go to check it for damage and so far it looks ok the injector pigtails, cold start pigtail and temp sensor pigtail on right side of head was replaced... I have to find out what it weighs to price shipping... as of right now ready to ship to...
2 grey interior kick panels L&R
Starter
alternator
driverside lower dash cover (black)
black park brake lever black trunk release
130mph speedometer
85mph speedometer
3 gage assy with digital clock(untested)
multifuntion sw hasnt been tested in some time worked last time i turned on the headlamps 4 years ago...
condensor- sold
fan shroud
air flow meter
monza cat back exhaust with test pipe
engine just rebuilt have reciepts
5spd trans- sold
2 grey interior kick panels L&R
Starter
alternator
driverside lower dash cover (black)
black park brake lever black trunk release
130mph speedometer
85mph speedometer
3 gage assy with digital clock(untested)
multifuntion sw hasnt been tested in some time worked last time i turned on the headlamps 4 years ago...
condensor- sold
fan shroud
air flow meter
monza cat back exhaust with test pipe
engine just rebuilt have reciepts
5spd trans- sold
Last edited by flightforlife07; Sep 24, 2011 at 10:29 AM.
Registered User
Joined: Oct 2011
Posts: 90
From: washington state
hello if you have it i need the hood release handle..just the plastic. i need a drivers side t top, but would take both if you have it. side vents off dash..whats left ? let me know
grg3210@yahoo.com
grg3210@yahoo.com
Registered User
Joined: Oct 2011
Posts: 90
From: washington state
looking for back 2 "cardboard " parts..rear light deck and panel behind drivers side. thanks, grg3210@yahoo.com
Thread Starter
Registered User
Joined: Jan 2005
Posts: 363
From: Quartz Hill, Ca
Hey guys I'm almost done parting this thing out just a few more things to go..
I still have the hood, doors, front and rear bumpers, rebuilt engine block, exhaust, 130mph speedo, analog clock set, storage buckets, rear hatch polyurethane bushing set, front control arms with steel sleeves removed to allow poly bushings, rear subframe assy (with control arms, spindle calipers and differential),grey interior kick panels, black underdash panels (i should have L&R), new clutch, and resurfaced flywheel, timing chain set, etc. Let me know what you neeed. I need to get rid of it all soon!
I still have the hood, doors, front and rear bumpers, rebuilt engine block, exhaust, 130mph speedo, analog clock set, storage buckets, rear hatch polyurethane bushing set, front control arms with steel sleeves removed to allow poly bushings, rear subframe assy (with control arms, spindle calipers and differential),grey interior kick panels, black underdash panels (i should have L&R), new clutch, and resurfaced flywheel, timing chain set, etc. Let me know what you neeed. I need to get rid of it all soon!
Last edited by flightforlife07; Dec 1, 2011 at 07:39 AM.
Registered User
Joined: Feb 2009
Posts: 303
Zx parting/out
well it has come to the unfortunate time that I get rid of my 280zx.. I have put a lot of work into the car and driven it all of 5 miles. if it doesn't sell whole I will be force to part it out. I am at the point that like most people I need the money, I would like to see it go to a nice home....
1980 280zx t-top 5 speed that has had the motor rebuilt ( .20" over bore new pistons rings and bearings, rebuilt N47 cylinder head, final compression ratio 10.25:1) all work done by adams metallizing.
New clutch, resurfaced flywheel, and new release bearing, rebuilt slave cylinder
new thermostat, Radiator hoses, water pump, new turbo oil pump
front suspension: energy suspension polyurethane bushing (control arms, sway bars).. I have polyurethane rear bushings need to be installed
Monza exhaust system from manifold back, Dual chrome tipped muffler, test pipe installed no cat
new timing chain gears chain and guide, New injectors and injector pigtails
Replace fenders, rear hatch and doors with rot free body panels
130mph speedometer from 79' 280zx and also analog clock gage set
high back seats need upholstery, body has surface rust
was in the process of converting interior to black and gray so i have some grey keck panels and various black interior parts.
1980 280zx t-top 5 speed that has had the motor rebuilt ( .20" over bore new pistons rings and bearings, rebuilt N47 cylinder head, final compression ratio 10.25:1) all work done by adams metallizing.
New clutch, resurfaced flywheel, and new release bearing, rebuilt slave cylinder
new thermostat, Radiator hoses, water pump, new turbo oil pump
front suspension: energy suspension polyurethane bushing (control arms, sway bars).. I have polyurethane rear bushings need to be installed
Monza exhaust system from manifold back, Dual chrome tipped muffler, test pipe installed no cat
new timing chain gears chain and guide, New injectors and injector pigtails
Replace fenders, rear hatch and doors with rot free body panels
130mph speedometer from 79' 280zx and also analog clock gage set
high back seats need upholstery, body has surface rust
was in the process of converting interior to black and gray so i have some grey keck panels and various black interior parts.
Thread
Thread Starter
Forum
Replies
Last Post
Bookmarks
